3710

Features

Spring-reset standards available to work non-stop in rocks

Spring-reset rock standard

The double-pivot design of the spring-reset standard uses tension spring force to return the standard to the working position.

For heavier-duty applications
Positive reset
Non-adjustable trip force; factory set at 2727-kg (6000-lb) nominal
Floats over buried rock
Unhooks from ledge rock

Land wheels on rigid models are tied to the Adjust-O-Cut bar for automatic setting for each width of cut

Depth stops are used for easy adjustment of depth

Land wheels help to stabilize the plow in both the working and transport positions. They also control the depth of plowing and work in conjunction with raising and lowering the plow.

Land wheels on rigid plows are tied to the Adjust-O-Cut bar for automatic setting for each width of cut.

A single wheel is standard on the six-bottom model; dual wheels are standard on the seven- and eight-bottom models and optional on the six-bottom model (recommended in softer soils).

Provides good trailing characteristics in transport.

Safety-trip standards for normal plowing conditions

Safety-trip standard

Safety-trip standards provide an economical means for protection—suited for areas without rocks:

No backing to reset, just raise
Shim-adjustable trip force
2727-kg (6000-lb) nominal trip force (set at the factory)
Smooth surfaces for good residue flow
Few moving parts equals high reliability

Shear-bolt coulters suited for areas without rocks

Shear-bolt coulters

Economical design of the shear-bolt coulters is suited for areas without rocks:

Few moving parts
Good depth adjustment range
Good lateral adjustment range

Adjustable width of cut

The operator can change the plow's width of cut to match the tractor horsepower and soil conditions.

Narrow in tough soil
Wider in lighter soil

3710 Rigid Plow

Turnbuckle

Hydraulic

The rigid plow has a width-of-cut range of 356 mm to 559 mm (14 in. to 22 in.) on land and 508 mm to 559 mm (20 in. to 22 in.) in furrow.

Economical manual adjustment (turnbuckle is standard equipment)
Convenient hydraulic cylinder adjustment is optional
Pointer and decal allow returning to a predetermined width of cut

3710 Flex Plow

The flex plow has 356 mm to 559 mm (14 in. to 22 in.) of cut.

Adjustments are made by adjusting two turnbuckles (arrows) to a predetermined length specified in the operator's manual.

High clearance handles heavy residue levels

Frame clearance for residue

Excellent fore-aft and vertical clearance between standards (arrows above) allows the soil and residue to freely flow through the plow:

Both rigid and flex plows are designed to handle tall and heavy residue levels.

Clearance

Fore and aft	Vertical

864 mm (34 in.)	851 mm (33.5 in.)

Scissor-type landing helps with tight turns on rigid models

Scissor-type landing adjustment

The rigid model uses a scissor-type landing adjustment to set the first bottom in relationship to the rear tractor tire for the different widths of cut:

Design uses minimum space, gives a clean-style appearance, and has a full range of adjustment.
Economical turnbuckle is used to make the adjustment.
Operator-supplied 76-mm x 203-mm (3-in. x 8-in.) American Society of Agricultural Engineers (ASAE) tie-bolt hydraulic cylinder may be used in place of a turnbuckle for in-furrow applications.

Adjustable-force cushion coulters available for rocky or normal field conditions

Adjustable-force cushion coulters are suited for rocky or normal field conditions:

Excellent rosette depth adjustment range
Good lateral adjustment range
Separate down-force adjustment
Overload protection to prevent damage

Flex models are equipped with dual, staggered Walk-Over™ land wheels

Land wheels have four adjustment positions

Land wheels on flex plows have four adjustment positions (arrow) to allow setting the assembly for 406-mm, 457-mm, or 508-mm (16-in., 18-in., or 20-in.) widths of cut or transport:

Depth stops are used for easy adjustment of the depth.

Dual, staggered Walk-Over wheels are standard on flex plows:

Allow the plow to trail like a cart
Distribute weight evenly between both wheels
Minimize bulldozing in soft soil
Allow better residue flow
Walk over obstacles and across dead furrows

Light-draft NU bottoms permit high-speed plowing

NU bottoms behind mainframe

The NU bottoms are set behind the mainframe to prevent the mainframe from becoming a pinch-point for residue. They are designed for light draft and high-speed plowing.

Operators often find they can plow a gear higher than with competitive plows
Greater productivity and fuel economy
Speeds up to 10 km/h (6 mph)

Available in 400-mm (16-in.) and 450-mm (18-in.) sizes with an unpolished finish.

The maximum plowing depth are as follows:

Bottom maximum	Plowing depth*
400 mm (16 in.)	305 mm (12 in.)
450 mm (18 in.)	356 mm (14 in.)

* In some soil conditions at plowing depths in the 254-mm to 356-mm (10-in. to 14-in.) range, soil may boil over the moldboard, resulting in poorly defined furrows.

Shares for NU bottoms

Both the NU 400 and the NU 450 come standard with heavy-duty, full-cut shares.

Variety of shares

A variety of shares are available through Parts to match the plowing conditions:

Image	Part	Description
1	NU400	Regular, narrow cut
2	NU400	Heavy duty, narrow cut
3	NU400	Heavy duty, full cut
4	NU450	Heavy duty, narrow cut
5	NU450	Heavy duty, full cut (standard equipment)
6	NU450	500-mm over-cut (for use when wide widths of cut or complete slicing is required)
7	NU450	Hard-faced gumbo (for heavy soil conditions when penetration is a problem
8	NU400	Hard-faced (for areas where abrasive soil causes rapid wear of heavy-duty shares—not for use in rocks)
9	NU450	Hard-faced (for areas where abrasive soil causes rapid wear of heavy-duty shares—not for use in rocksfor)

The gumbo moldboard (A32211) is available for NU 400 bottom and is recommended for use in heavy soil (gumbo) conditions. It is similar to the NU 400 bottom except that it has less area at the wing tip.

Moldboard will not be forced upward by soil movement as much as NU 400.
Permits soil to push off easier for better scouring and lighter draft.

John Deere furnishes a replacement share for any John Deere plow share that breaks before the share reaches the following wear limits (labor not included; wear to be measured perpendicularly across the middle of the front bolt hole):

13-mm (1/2-in.) wear, 89 mm (3.5 in.) remaining.

Trashboards for NU bottoms

Trashboard

Plastic or steel trashboards can be added to NU bottoms to improve coverage in tall, heavy residue. Plastic trashboards are only recommended for non-abrasive soils where scouring is a problem with steel trashboards.

Show More Show Less

Specs

Specifications

ADD MODEL

Add Model

ADD MODEL

Select Different Model

Specifications

Select up to 4 models to compare specifications

John Deere

3710

Moldboard Plow

Export to Excel

1 2

Hitch

Type
Steering	Integral, in-furrow NoIntegral, on-land NoSemi-integral, on-land NoDrawn, in-furrow Yes - 6, 7Drawn, on-land Yes - 6,7,8,9,10
Reversible	No

No. of bottoms

Option 1	6
Option 2	7
Option 3	8
Option 4	9
Option 5	10
Option 6
Option 7
Option 8

Total width of cut

Adjustment	Manual
Option 1	Range 350 to 550 mm 14 to 22 in. Hydraulic
Option 2	(14 - 22) manually adjusted (on-land) in.
Option 3	(14 - 22) manually adjusted (on-land) in.
Option 4
Option 5
Option 6
Option 7
Option 8

Weight (approximate)

Option 1
Option 2
Option 3
Option 4
Option 5
Option 6
Option 7
Option 8

Clearances

Vertical	850 mm 33.5 in.
Fore-aft	875 mm 34 in.

Standards

Shearbolt	No
Safety trip	Yes
Spring reset	Yes
Hydraulic	No

Coulters

Option 1	Yes
Option 2	Yes
Option 3

Bottoms

Option 1	Plowing depth 350 mm 14 in. 254 mm 10 in.
Option 2
Option 3
Option 4
Option 5	Reversible Bottom -Steel
Option 6	Reversible Bottom -Steel

Frame

Option 1	200 x 200 mm 8 x 8 in.
Option 2
Option 3
Explandable	No

Horsepower required

Option 1
Option 2
Option 3
Option 4

Landing

Type

Gauge wheel

Type

Tires

Type

Trashboards

Type

Additional information

Date collected

Show More Show Less

Used Equipment Search / Filter

3710Moldboard Plow

Features

Spring-reset standards available to work non-stop in rocks

Land wheels on rigid models are tied to the Adjust-O-Cut bar for automatic setting for each width of cut

Safety-trip standards for normal plowing conditions

Shear-bolt coulters suited for areas without rocks

Adjustable width of cut

3710 Rigid Plow

3710 Flex Plow

High clearance handles heavy residue levels

Scissor-type landing helps with tight turns on rigid models

Adjustable-force cushion coulters available for rocky or normal field conditions

Flex models are equipped with dual, staggered Walk-Over™ land wheels

Light-draft NU bottoms permit high-speed plowing

Bottom maximum

Plowing depth*

Shares for NU bottoms

Trashboards for NU bottoms

Specs

Specifications

Add Model

Specifications

John Deere

3710

Hitch

No. of bottoms

Total width of cut

Weight (approximate)

Clearances

Standards

Coulters

Bottoms

Frame

Horsepower required

Landing

Gauge wheel

Tires

Trashboards

Additional information

Accessories and Attachments

We dug around but couldn't find the page you're looking for.

CUSTOMER REVIEWS

3710
Moldboard Plow