We dug around but couldn't find the page you're looking for.
Try our Home Page
404 Error
Page not found
913
V-Ripper
- Adjustable standard spacing prevents side movement
- V-pattern frame promotes leading-edge shattering
- LaserRip™ Extreme points
- Heavy-duty steel ripper points
View Product Brochure
Features
Expand AllCollapse All
Soil probe
913 V-Ripper 
Low and high positions on 3-point mast
Soil probe helps to determine proper operating depth
Soil probeThe soil probe helps operators to determine the proper operating depth of their ripper points,
38 mm (1.5 in.) below the bottom of the compaction layer.
The probe allows obtaining the maximum amount of soil fracturing from the entire family of John Deere ripper points. Marked in 51-mm (2-in.) increments from 254 mm to 559 mm (10 in. to 22 in.), the probe provides accurate feedback of compaction layer depth.
It is stored on the mainframe of the ripper for convenient access. The operator's manual explains the proper use of the soil probe.
Strong V-pattern frame promotes leading-edge shattering of center shank and material flow
913 V-Ripper The frame design of the 913 V-Ripper positions the standards in a V pattern:
- Promotes leading-edge shattering of the center shank and material flow through the machine
The 127-mm x 178-mm (5-in. x 7-in.) cross-section frame has 10-mm (3/8-in.) thick walls:
- Provides strength to handle tractors of up to 150 power take-off (PTO) horsepower
- Same frame-size tubing as non-expandable 915 V-Ripper
- Parking stands are included in base equipment
Two-position integral hitch to meet operator requirements
Low and high positions on 3-point mast3-point hitch hookup is for Category 2 or 3N tractors.
The integral hitch can be set to two positions:
- 1 = Low position
Gives maximum transport clearance and allows ripping to approximately 508 mm (20 in.) deep with the 838-mm (33-in.) standards. - 2 = High position
Enables ripping to a maximum depth of 584 mm (23 in.) deep with the 838-mm (33-in.) standards.
Specs
Specifications
Add Model
Specifications | ||||
|---|---|---|---|---|
| Select up to 4 models to compare specifications | John Deere913V-Ripper |
Tool configuration
| Type | V-ripper | |||
|---|---|---|---|---|
| Option 1 | 3-standard, 20-in. spacing | |||
| Option 2 | 3-standard, 25-in. spacing | |||
| Option 3 | 3-standard, 30-in. spacing | |||
| Option 4 | ||||
| Option 5 | ||||
| Option 6 | ||||
| Option 7 | ||||
| Option 8 | ||||
| Option 9 | ||||
| Option 10 | ||||
| Option 11 | ||||
| Option 12 | ||||
| Option 13 | ||||
| Option 14 | ||||
| Option 15 | ||||
| Option 16 | ||||
| Option 17 | ||||
| Option 18 | ||||
| Option 19 | ||||
| Option 20 | ||||
| Option 21 | ||||
| Option 22 |
Working width
| Option 1 | 8, 4 ft, in. | |||
|---|---|---|---|---|
| Option 2 | 10, 5 ft, in. | |||
| Option 3 | 12, 6 ft, in. | |||
| Option 4 | ||||
| Option 5 | ||||
| Option 6 | ||||
| Option 7 | ||||
| Option 8 | ||||
| Option 9 | ||||
| Option 10 | ||||
| Option 11 | ||||
| Option 12 | ||||
| Option 13 | ||||
| Option 14 | ||||
| Option 15 | ||||
| Option 16 | ||||
| Option 17 | ||||
| Option 18 | ||||
| Option 19 | ||||
| Option 20 | ||||
| Option 21 | ||||
| Option 22 |
Transport width
| Option 1 | 7 ft | |||
|---|---|---|---|---|
| Option 2 | 7 ft | |||
| Option 3 | 7 ft | |||
| Option 4 | ||||
| Option 5 | ||||
| Option 6 | ||||
| Option 7 | ||||
| Option 8 | ||||
| Option 9 | ||||
| Option 10 | ||||
| Option 11 | ||||
| Option 12 | ||||
| Option 13 | ||||
| Option 14 | ||||
| Option 15 | ||||
| Option 16 | ||||
| Option 17 | ||||
| Option 18 | ||||
| Option 19 | ||||
| Option 20 | ||||
| Option 21 | ||||
| Option 22 |
Operating depth
| Maximum | 23 in. |
|---|
Frame
| Size | ||||
|---|---|---|---|---|
| Maximum underframe clearance |
Operating speed
| Miles per hour |
|---|
Horsepower required
| Horsepower per standard |
|---|
Depth control
| Option 1 | Intergral units are controlled by tractor, rockshaft, and gauge wheels | |||
|---|---|---|---|---|
| Option 2 | ||||
| Option 3 |
Hydraulic requirements
| Option 1 | ||||
|---|---|---|---|---|
| Option 2 |
Hitch
| Options | Intergral | |||
|---|---|---|---|---|
| Three-point hitch requirements | Cat 2 or 3N with Quick Coupler; Cat 3N without Quick-Coupler | |||
| Pull-type description |
Standard options
| Spacings | 20, 25, 30 in. | |||
|---|---|---|---|---|
| Option 1 | Trip force 12,000 lbStandard type Straight or parabolic with wear shin Shear-bolt | |||
| Option 2 | Trip force 5600 lbStandard type Straight with wear shin or parabolic Safety-trip | |||
| Option 3 | Trip force 5300 lbStandard type Straight with wear shin or parabolic Cushion-trip | |||
| Option 4 | Trip force 3200 - 5300 lbStandard type Parabolic Spring-reset rock standard |
Ground-engaging components
| Options | 2.25-in.point, 2.25-in. chrome single or double carbide cap; 2-3/4-in. (70 mm), 5-in. (127 mm), 7-in. (178 mm) LaserRip points optional.or 10-in. (254 mm) |
|---|
Coulters
| Description | ||||
|---|---|---|---|---|
| Type | ||||
| Pounds of force | ||||
| Blades |
Closing wheel attachment
| Description | ||||
|---|---|---|---|---|
| Down force | ||||
| Size | ||||
| Spacing | ||||
| Angle adjustments |
Stabilizer/gauge wheels
| Type | ||||
|---|---|---|---|---|
| Wheels | ||||
| Tires |
Pull-type wheels
| Description | ||||
|---|---|---|---|---|
| Additional feature | ||||
| Option 1 | ||||
| Option 2 | ||||
| Option 3 | ||||
| Option 4 |
Additional information
| Date collected |
|---|
Accessories and Attachments
Try our Home Page
CUSTOMER REVIEWS
No reviews have been created.